MONTAGEANLEITUNG
26 Schritte zur fertigen Freistehende motorisierte Pergola.
Freistehende Aluminium-Pergola mit motorisiertem Lamellendach — sechs Perimetergrößen (3×3 → 4×6) aus einer gemeinsamen 26-Schritt-Prozedur.
-
01
Eckverbindungssätze vorbereiten
Pre-build the four corner connection sets — set projection vs width orientation now.
RAHMEN12 Min. -
02
Vorderen U-Rahmen bauen
Insert the front C-1 gutter into B-1/B-2 pillars to form the front U-frame on the ground.
RAHMEN18 Min. -
03
Hinteren U-Rahmen bauen
Repeat for the rear C-2 gutter into A-1/A-2 pillars — keep both U-frames square.
RAHMEN18 Min. -
04
Die U-förmigen Rahmen anheben
Lift both U-frames simultaneously — two installers per frame, mind the powder coating.
RAHMEN25 Min. -
05
Linkes Seitenprofil D-1 montieren
Install the left D-1 side perimeter profile between the two U-frames.
RAHMEN18 Min. -
06
Rechtes Seitenprofil D-2 montieren
Install the right D-2 side perimeter profile — frame is now closed.
RAHMEN18 Min. -
07
Diagonalen und Entwässerungsstopfen prüfen
Verify diagonals match the size table (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat drainage plugs.
RAHMEN15 Min. -
08
F-Regenrinnen in Projektionsrichtung montieren
Mount F gutters in the projection direction.
RAHMEN18 Min. -
09
E-Regenrinnen in Breitenrichtung montieren
Mount E gutters in the width direction — perimeter complete.
RAHMEN18 Min. -
10
Obere Regenrinnen von oben fixieren
Fix all top gutters from above with 3.9 mm screws.
RAHMEN15 Min. -
11
Gummiverbindungen abdichten
Seal rubber junctions at all gutter intersections — neutral silicone bead.
RAHMEN12 Min. -
12
Standard-Lamellen vorbereiten
Pre-cut and prepare the standard PN-LM-500 lamellas to width.
LAMELLEN20 Min. -
13
Motorlamelle vorbereiten
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELLEN15 Min. -
14
Motor auf D-1-Profil montieren
Mount the PN-MT-500 motor on the D-1 profile per code map orientation.
LAMELLEN25 Min. -
15
Motorlamelle montieren
Install the motor blade onto the rotation pin first — verifies free movement.
LAMELLEN20 Min. -
16
Motorarm justieren
Adjust the motor arm angle so the motor blade closes flush.
LAMELLEN18 Min. -
17
Restliche Lamellen montieren
Insert the remaining standard lamellas one by one — verify rotation by hand.
LAMELLEN30 Min. -
18
Bewegungsarme montieren
Install the PN-AR-500 movement arms linking all blades to the motor blade.
LAMELLEN25 Min. -
19
Bewegungsarm-Abdeckungen montieren
Cap with the PN-CV-500 movement-arm cover profiles.
LAMELLEN15 Min. -
20
Säulenabdeckungen montieren
Mount the PN-DZ-510 pillar covers (4 corners).
ABSCHLUSS12 Min. -
21
Hinteres Abdeckprofil montieren
Install the PN-CV-501 rear cover profile.
ABSCHLUSS12 Min. -
22
Vorderes Abdeckprofil montieren
Install the PN-CV-502 front cover profile.
ABSCHLUSS12 Min. -
23
Eckabdeckungen montieren
Install the corner cover trims at the four upper corners.
ABSCHLUSS15 Min. -
24
Motorkabel verlegen
Route the motor cables down through the designated pillar channel.
ABSCHLUSS15 Min. -
25
LED-Streifen und PVC-Abdeckung montieren
Install the LED strip into the gutter recess and snap on the PVC cover.
ABSCHLUSS18 Min. -
26
Elektrische Verkabelung fertigstellen
Complete electrical wiring at the controller — verify motor direction and end-stops.
ABSCHLUSS30 Min.
Über diese freistehende motorisierte pergola-Montageanleitung
Luxa Aperio 500 — Freistehende motorisierte Pergola · LuxaShade aluminium roof family. 26 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Warum die offizielle PONARC × LuxaShade-Anleitung befolgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januar 2026 · DE