GUIDE D'INSTALLATION
26 étapes vers un(e) Pergola motorisée autoportante terminé(e).
Pergola autoportante en aluminium avec toit à lames motorisé — six dimensions (3×3 → 4×6) partageant une procédure unique en 26 étapes.
-
01
Préparer les jeux de connexion d'angle
Pre-build the four corner connection sets — set projection vs width orientation now.
STRUCTURE12 min -
02
Construire le cadre U avant
Insert the front C-1 gutter into B-1/B-2 pillars to form the front U-frame on the ground.
STRUCTURE18 min -
03
Construire le cadre U arrière
Repeat for the rear C-2 gutter into A-1/A-2 pillars — keep both U-frames square.
STRUCTURE18 min -
04
Lever les cadres en U
Lift both U-frames simultaneously — two installers per frame, mind the powder coating.
STRUCTURE25 min -
05
Installer le profil latéral gauche D-1
Install the left D-1 side perimeter profile between the two U-frames.
STRUCTURE18 min -
06
Installer le profil latéral droit D-2
Install the right D-2 side perimeter profile — frame is now closed.
STRUCTURE18 min -
07
Vérifier les diagonales et les bouchons de drainage
Verify diagonals match the size table (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat drainage plugs.
STRUCTURE15 min -
08
Installer les gouttières F dans le sens de la projection
Mount F gutters in the projection direction.
STRUCTURE18 min -
09
Installer les gouttières E dans le sens de la largeur
Mount E gutters in the width direction — perimeter complete.
STRUCTURE18 min -
10
Fixer les gouttières supérieures par le dessus
Fix all top gutters from above with 3.9 mm screws.
STRUCTURE15 min -
11
Sceller les joints en caoutchouc
Seal rubber junctions at all gutter intersections — neutral silicone bead.
STRUCTURE12 min -
12
Préparer les lames standard
Pre-cut and prepare the standard PN-LM-500 lamellas to width.
LAMES20 min -
13
Préparer la lame motrice
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMES15 min -
14
Installer le moteur sur le profil D-1
Mount the PN-MT-500 motor on the D-1 profile per code map orientation.
LAMES25 min -
15
Installer la lame motrice
Install the motor blade onto the rotation pin first — verifies free movement.
LAMES20 min -
16
Ajuster le bras moteur
Adjust the motor arm angle so the motor blade closes flush.
LAMES18 min -
17
Installer les lames restantes
Insert the remaining standard lamellas one by one — verify rotation by hand.
LAMES30 min -
18
Installer les bras de mouvement
Install the PN-AR-500 movement arms linking all blades to the motor blade.
LAMES25 min -
19
Installer les caches des bras de mouvement
Cap with the PN-CV-500 movement-arm cover profiles.
LAMES15 min -
20
Installer les caches de poteau
Mount the PN-DZ-510 pillar covers (4 corners).
FINITION12 min -
21
Installer le profil de fermeture arrière
Install the PN-CV-501 rear cover profile.
FINITION12 min -
22
Installer le profil de fermeture avant
Install the PN-CV-502 front cover profile.
FINITION12 min -
23
Installer les caches d'angle
Install the corner cover trims at the four upper corners.
FINITION15 min -
24
Faire passer les câbles moteur
Route the motor cables down through the designated pillar channel.
FINITION15 min -
25
Installer la bande LED et son cache PVC
Install the LED strip into the gutter recess and snap on the PVC cover.
FINITION18 min -
26
Terminer le câblage électrique
Complete electrical wiring at the controller — verify motor direction and end-stops.
FINITION30 min
À propos de ce guide d'installation pergola motorisée autoportante
Luxa Aperio 500 — Pergola motorisée autoportante · LuxaShade aluminium roof family. 26 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Pourquoi suivre la procédure officielle PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Janvier 2026 · FR