GHID DE INSTALARE
26 pași până la un(o) Pergolă motorizată independentă finalizat(ă).
Pergolă independentă din aluminiu cu acoperiș cu lamele motorizate — șase dimensiuni (3×3 → 4×6) dintr-o procedură unică în 26 de pași.
-
01
Pregătiți seturile de conexiune de colț
Pre-build the four corner connection sets — set projection vs width orientation now.
CADRU12 min -
02
Construiți cadrul U frontal
Insert the front C-1 gutter into B-1/B-2 pillars to form the front U-frame on the ground.
CADRU18 min -
03
Construiți cadrul U posterior
Repeat for the rear C-2 gutter into A-1/A-2 pillars — keep both U-frames square.
CADRU18 min -
04
Ridicați cadrele în formă de U
Lift both U-frames simultaneously — two installers per frame, mind the powder coating.
CADRU25 min -
05
Instalați profilul lateral stâng D-1
Install the left D-1 side perimeter profile between the two U-frames.
CADRU18 min -
06
Instalați profilul lateral drept D-2
Install the right D-2 side perimeter profile — frame is now closed.
CADRU18 min -
07
Verificați diagonalele și dopurile de drenaj
Verify diagonals match the size table (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat drainage plugs.
CADRU15 min -
08
Instalați jgheaburile F pe direcția proiecției
Mount F gutters in the projection direction.
CADRU18 min -
09
Instalați jgheaburile E pe direcția lățimii
Mount E gutters in the width direction — perimeter complete.
CADRU18 min -
10
Fixați jgheaburile superioare de sus
Fix all top gutters from above with 3.9 mm screws.
CADRU15 min -
11
Etanșați îmbinările din cauciuc
Seal rubber junctions at all gutter intersections — neutral silicone bead.
CADRU12 min -
12
Pregătiți lamelele standard
Pre-cut and prepare the standard PN-LM-500 lamellas to width.
LAMELE20 min -
13
Pregătiți lamela motoarei
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELE15 min -
14
Instalați motorul pe profilul D-1
Mount the PN-MT-500 motor on the D-1 profile per code map orientation.
LAMELE25 min -
15
Instalați lamela motoare
Install the motor blade onto the rotation pin first — verifies free movement.
LAMELE20 min -
16
Reglați brațul motor
Adjust the motor arm angle so the motor blade closes flush.
LAMELE18 min -
17
Instalați lamelele rămase
Insert the remaining standard lamellas one by one — verify rotation by hand.
LAMELE30 min -
18
Instalați brațele de mișcare
Install the PN-AR-500 movement arms linking all blades to the motor blade.
LAMELE25 min -
19
Instalați capacele brațelor de mișcare
Cap with the PN-CV-500 movement-arm cover profiles.
LAMELE15 min -
20
Instalați capacele stâlpilor
Mount the PN-DZ-510 pillar covers (4 corners).
FINISARE12 min -
21
Instalați profilul de închidere posterior
Install the PN-CV-501 rear cover profile.
FINISARE12 min -
22
Instalați profilul de închidere frontal
Install the PN-CV-502 front cover profile.
FINISARE12 min -
23
Instalați capacele de colț
Install the corner cover trims at the four upper corners.
FINISARE15 min -
24
Trasați cablurile motorului
Route the motor cables down through the designated pillar channel.
FINISARE15 min -
25
Instalați banda LED și capacul PVC
Install the LED strip into the gutter recess and snap on the PVC cover.
FINISARE18 min -
26
Finalizați cablajul electric
Complete electrical wiring at the controller — verify motor direction and end-stops.
FINISARE30 min
Despre acest ghid de instalare pergolă motorizată independentă
Luxa Aperio 500 — Pergolă motorizată independentă · LuxaShade aluminium roof family. 26 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
De ce să urmați procedura oficială PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Ianuarie 2026 · RO