MONTAGEANLEITUNG
16 Schritte zur fertigen Wandmontierte manuelle bioklimatische Pergola.
Wandmontierte bioklimatische Aluminium-Pergola mit manueller Handbedienung — Wandlatte PN-WM-500 ersetzt den hinteren freistehenden Rahmen, nur zwei vordere Säulen. Drei Perimetergrößen aus einer gemeinsamen 16-Schritt-Prozedur.
-
01
Wandlatten-Linie anzeichnen
Mark the wall ledger line — the entire roof reference for a wall-mount install.
RAHMEN15 Min. -
02
Wandlatte PN-WM-500 verankern
Anchor PN-WM-500 wall ledger — replaces the rear free-standing frame.
RAHMEN25 Min. -
03
Die zwei vorderen Fußplatten platzieren
Place the two front PN-FP-500 foot plates parallel to the wall ledger.
RAHMEN18 Min. -
04
Die zwei vorderen Säulen aufrichten
Lift the two front PN-DZ-500 pillars onto their foot plate studs.
RAHMEN22 Min. -
05
Vordere Trägerregenrinne montieren
Install the front PN-GU-500 carrier gutter — match height to wall ledger ±2 mm.
RAHMEN18 Min. -
06
Seitenregenrinnen (Front zu Wand) montieren
Install left and right side gutters — wall-side ends fix to PN-WM-500 ledger.
RAHMEN22 Min. -
07
Eckverbindungen abdichten
Apply neutral-cure silicone bead at all four upper corner joints.
RAHMEN12 Min. -
08
Lamellen-Schienen PN-RA-500 montieren
Slide PN-RA-500 blade rails into the frame channels — pre-set pivot positions.
LAMELLEN18 Min. -
09
Lamellen vorbereiten
Prepare the louvre blades (PN-LM-500 opening + PN-LM-501 fixed reference).
LAMELLEN18 Min. -
10
Feste Lamelle PN-LM-501 montieren
Install the PN-LM-501 fixed lamella against the wall ledger — closed-position reference.
LAMELLEN15 Min. -
11
Öffnende Lamellen PN-LM-500 montieren
Install the PN-LM-500 opening lamellas (back/wall side first) — equal pitch.
LAMELLEN25 Min. -
12
Manuelles Gestänge anschließen
Connect the manual synchronization linkage — all opening blades move together.
LAMELLEN18 Min. -
13
Manuelle Handkurbel PN-HD-500 montieren
Install the PN-HD-500 manual handle — front-side rail, smooth crank cycle.
LAMELLEN18 Min. -
14
Endlagen einstellen und Abdeckungen montieren
Set open / close end-stops and install front pillar caps + gutter closing profiles.
ABSCHLUSS18 Min. -
15
Entwässerungsausläufe montieren und Endtest
Connect drainage outlets in front pillars and complete final functional test.
ABSCHLUSS18 Min. -
16
Reinigen und übergeben
Clean, demonstrate manual operation to customer, hand over warranty card.
ABSCHLUSS12 Min.
Über diese wandmontierte manuelle bioklimatische pergola-Montageanleitung
Luxa Sereno 500M Wall — Wandmontierte manuelle bioklimatische Pergola · LuxaShade aluminium roof family. 16 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Warum die offizielle PONARC × LuxaShade-Anleitung befolgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januar 2026 · DE