MONTAGEANLEITUNG
18 Schritte zur fertigen Manuelle bioklimatische Pergola.
Freistehende bioklimatische Aluminium-Pergola mit manueller Kurbelbedienung — kein Motor, keine Firmware, drei Perimetergrößen aus einer gemeinsamen 18-Schritt-Prozedur.
-
01
Systemlayout und Bezugslinie
Set the system datum and mark the four foot-plate centres on the slab.
RAHMEN18 Min. -
02
Fußplatten platzieren
Place the four PN-FP-500 foot plates and anchor with M10 buldex.
RAHMEN25 Min. -
03
Die vier Säulen aufrichten
Lift each PN-DZ-500 pillar onto its foot plate stud — two installers per pillar.
RAHMEN25 Min. -
04
Hintere Trägerregenrinne montieren
Install the rear PN-GU-500 carrier gutter — slope 1.5% toward the front.
RAHMEN18 Min. -
05
Vordere Trägerregenrinne montieren
Install the front PN-GU-500 carrier gutter — match heights within 2 mm.
RAHMEN18 Min. -
06
Seitenregenrinnen montieren
Install left and right PN-GU-501 side gutters — verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 cm).
RAHMEN25 Min. -
07
Eckverbindungen abdichten
Apply neutral-cure silicone bead at all four upper corner joints.
RAHMEN12 Min. -
08
Lamellen-Seitenschienen montieren
Slide PN-LR-500 blade side rails into the frame — pre-set pivot positions.
LAMELLEN18 Min. -
09
Lamellen vorbereiten
Prepare the louvre blades — fit pivot pins, lay out on a clean covered surface.
LAMELLEN18 Min. -
10
Erste Lamelle montieren
Install the first blade — verify free rotation and flush closed position.
LAMELLEN15 Min. -
11
Lamellenfeld komplettieren
Complete the blade array — equal pitch using a spacer gauge.
LAMELLEN25 Min. -
12
Manuelles Gestänge anschließen
Connect PN-SC-500 manual linkage — all blades must move together.
LAMELLEN20 Min. -
13
Manuelles Kurbelgetriebe montieren
Install PN-CR-500 crank gear and PN-GT-500 drive shaft — test full cycle.
LAMELLEN20 Min. -
14
Öffnen-/Schließen-Endlagen einstellen
Set crank end-stops for fully closed and fully open positions.
LAMELLEN18 Min. -
15
Abdeckprofile montieren
Install PN-CP-500 pillar caps and PN-CP-501 gutter closing profiles.
ABSCHLUSS15 Min. -
16
Entwässerungsausläufe montieren
Connect PN-WT-100/PN-WT-101 drainage tubes inside front pillars and test water flow.
ABSCHLUSS18 Min. -
17
Endfunktionstest
Final functional test — open, close, verify even closure across array.
ABSCHLUSS12 Min. -
18
Reinigen und übergeben
Clean powder coating, demonstrate to customer, hand over warranty card.
ABSCHLUSS12 Min.
Über diese manuelle bioklimatische pergola-Montageanleitung
Luxa Sereno 500M — Manuelle bioklimatische Pergola · LuxaShade aluminium roof family. 18 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Warum die offizielle PONARC × LuxaShade-Anleitung befolgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januar 2026 · DE