GUIDE D'INSTALLATION
18 étapes vers un(e) Pergola bioclimatique manuelle terminé(e).
Pergola bioclimatique autoportante en aluminium à manivelle manuelle — sans moteur, sans firmware, trois dimensions partageant une procédure unique en 18 étapes.
-
01
Implantation du système et ligne de référence
Set the system datum and mark the four foot-plate centres on the slab.
STRUCTURE18 min -
02
Poser les plaques de pied
Place the four PN-FP-500 foot plates and anchor with M10 buldex.
STRUCTURE25 min -
03
Lever les quatre poteaux
Lift each PN-DZ-500 pillar onto its foot plate stud — two installers per pillar.
STRUCTURE25 min -
04
Installer la gouttière porteuse arrière
Install the rear PN-GU-500 carrier gutter — slope 1.5% toward the front.
STRUCTURE18 min -
05
Installer la gouttière porteuse avant
Install the front PN-GU-500 carrier gutter — match heights within 2 mm.
STRUCTURE18 min -
06
Installer les gouttières latérales
Install left and right PN-GU-501 side gutters — verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 cm).
STRUCTURE25 min -
07
Sceller les joints d'angle
Apply neutral-cure silicone bead at all four upper corner joints.
STRUCTURE12 min -
08
Installer les rails latéraux des lames
Slide PN-LR-500 blade side rails into the frame — pre-set pivot positions.
LAMES18 min -
09
Préparer les lames
Prepare the louvre blades — fit pivot pins, lay out on a clean covered surface.
LAMES18 min -
10
Installer la première lame
Install the first blade — verify free rotation and flush closed position.
LAMES15 min -
11
Compléter le champ de lames
Complete the blade array — equal pitch using a spacer gauge.
LAMES25 min -
12
Connecter la tringlerie manuelle
Connect PN-SC-500 manual linkage — all blades must move together.
LAMES20 min -
13
Installer la manivelle manuelle
Install PN-CR-500 crank gear and PN-GT-500 drive shaft — test full cycle.
LAMES20 min -
14
Régler les fins de course d'ouverture / fermeture
Set crank end-stops for fully closed and fully open positions.
LAMES18 min -
15
Installer les profils de fermeture
Install PN-CP-500 pillar caps and PN-CP-501 gutter closing profiles.
FINITION15 min -
16
Installer les évacuations de drainage
Connect PN-WT-100/PN-WT-101 drainage tubes inside front pillars and test water flow.
FINITION18 min -
17
Test fonctionnel final
Final functional test — open, close, verify even closure across array.
FINITION12 min -
18
Nettoyer et remettre au client
Clean powder coating, demonstrate to customer, hand over warranty card.
FINITION12 min
À propos de ce guide d'installation pergola bioclimatique manuelle
Luxa Sereno 500M — Pergola bioclimatique manuelle · LuxaShade aluminium roof family. 18 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Pourquoi suivre la procédure officielle PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Janvier 2026 · FR