INSTALLATIEHANDLEIDING
18 stappen naar een voltooide Handbediende bioklimatische pergola.
Vrijstaande aluminium bioklimatische pergola met handmatige zwengel — geen motor, geen firmware, drie omtreksmaten uit één gedeelde 18-stappenprocedure.
-
01
Systeem-uitzetten en referentielijn
Set the system datum and mark the four foot-plate centres on the slab.
FRAME18 min -
02
Voetplaten plaatsen
Place the four PN-FP-500 foot plates and anchor with M10 buldex.
FRAME25 min -
03
De vier kolommen oprichten
Lift each PN-DZ-500 pillar onto its foot plate stud — two installers per pillar.
FRAME25 min -
04
Achterste draaggoten monteren
Install the rear PN-GU-500 carrier gutter — slope 1.5% toward the front.
FRAME18 min -
05
Voorste draaggoten monteren
Install the front PN-GU-500 carrier gutter — match heights within 2 mm.
FRAME18 min -
06
Zijgoten monteren
Install left and right PN-GU-501 side gutters — verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 cm).
FRAME25 min -
07
Hoekverbindingen afdichten
Apply neutral-cure silicone bead at all four upper corner joints.
FRAME12 min -
08
Lamellen-zijrails monteren
Slide PN-LR-500 blade side rails into the frame — pre-set pivot positions.
LAMELLEN18 min -
09
Lamellen voorbereiden
Prepare the louvre blades — fit pivot pins, lay out on a clean covered surface.
LAMELLEN18 min -
10
Eerste lamel monteren
Install the first blade — verify free rotation and flush closed position.
LAMELLEN15 min -
11
Lamellenveld voltooien
Complete the blade array — equal pitch using a spacer gauge.
LAMELLEN25 min -
12
Handmatige aandrijving aansluiten
Connect PN-SC-500 manual linkage — all blades must move together.
LAMELLEN20 min -
13
Handmatige zwengel monteren
Install PN-CR-500 crank gear and PN-GT-500 drive shaft — test full cycle.
LAMELLEN20 min -
14
Open/dicht-eindstanden instellen
Set crank end-stops for fully closed and fully open positions.
LAMELLEN18 min -
15
Afdekprofielen monteren
Install PN-CP-500 pillar caps and PN-CP-501 gutter closing profiles.
AFWERKING15 min -
16
Afwateringsuitlopen monteren
Connect PN-WT-100/PN-WT-101 drainage tubes inside front pillars and test water flow.
AFWERKING18 min -
17
Eindtest werking
Final functional test — open, close, verify even closure across array.
AFWERKING12 min -
18
Schoonmaken en overdragen
Clean powder coating, demonstrate to customer, hand over warranty card.
AFWERKING12 min
Over deze handbediende bioklimatische pergola-installatiehandleiding
Luxa Sereno 500M — Handbediende bioklimatische pergola · LuxaShade aluminium roof family. 18 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Waarom de officiële PONARC × LuxaShade-procedure volgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januari 2026 · NL