РУКОВОДСТВО ПО МОНТАЖУ
18 шагов до готового Биоклиматическая пергола с ручным управлением.
Отдельностоящая алюминиевая биоклиматическая пергола с ручным приводом — без электропривода, без прошивки, три размера периметра по единой 18-шаговой процедуре.
-
01
Разметка системы и контрольная линия
Set the system datum and mark the four foot-plate centres on the slab.
КАРКАС18 мин -
02
Установить опорные пластины
Place the four PN-FP-500 foot plates and anchor with M10 buldex.
КАРКАС25 мин -
03
Поднять четыре стойки
Lift each PN-DZ-500 pillar onto its foot plate stud — two installers per pillar.
КАРКАС25 мин -
04
Смонтировать задний несущий водосток
Install the rear PN-GU-500 carrier gutter — slope 1.5% toward the front.
КАРКАС18 мин -
05
Смонтировать передний несущий водосток
Install the front PN-GU-500 carrier gutter — match heights within 2 mm.
КАРКАС18 мин -
06
Смонтировать боковые водостоки
Install left and right PN-GU-501 side gutters — verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 cm).
КАРКАС25 мин -
07
Уплотнить угловые соединения
Apply neutral-cure silicone bead at all four upper corner joints.
КАРКАС12 мин -
08
Смонтировать боковые направляющие ламелей
Slide PN-LR-500 blade side rails into the frame — pre-set pivot positions.
ЛАМЕЛИ18 мин -
09
Подготовить ламели
Prepare the louvre blades — fit pivot pins, lay out on a clean covered surface.
ЛАМЕЛИ18 мин -
10
Установить первую ламель
Install the first blade — verify free rotation and flush closed position.
ЛАМЕЛИ15 мин -
11
Завершить набор ламелей
Complete the blade array — equal pitch using a spacer gauge.
ЛАМЕЛИ25 мин -
12
Подключить ручной привод-тягу
Connect PN-SC-500 manual linkage — all blades must move together.
ЛАМЕЛИ20 мин -
13
Установить ручную рукоятку привода
Install PN-CR-500 crank gear and PN-GT-500 drive shaft — test full cycle.
ЛАМЕЛИ20 мин -
14
Настроить концевики открытия / закрытия
Set crank end-stops for fully closed and fully open positions.
ЛАМЕЛИ18 мин -
15
Установить закрывающие профили
Install PN-CP-500 pillar caps and PN-CP-501 gutter closing profiles.
ОТДЕЛКА15 мин -
16
Установить водоотводные сливы
Connect PN-WT-100/PN-WT-101 drainage tubes inside front pillars and test water flow.
ОТДЕЛКА18 мин -
17
Финальный функциональный тест
Final functional test — open, close, verify even closure across array.
ОТДЕЛКА12 мин -
18
Очистить и передать клиенту
Clean powder coating, demonstrate to customer, hand over warranty card.
ОТДЕЛКА12 мин
Об этом руководстве по монтажу биоклиматическая пергола с ручным управлением
Luxa Sereno 500M — Биоклиматическая пергола с ручным управлением · LuxaShade aluminium roof family. 18 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Почему важно следовать официальной процедуре PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Январь 2026 · RU